vault backup: 2025-12-10 16:47:02

2025-12-10.md

@@ -55,6 +55,8 @@ and costed a job half a million in profit,
 what I took away was that we sold high-risk scope
 without knowing what was required _and without qualification_.
 
+***
+
 Others have suggested creating new assemblies grouped by manufacturer,
 which I'm not a fan of.
 While it's true that similar implementations

banjo-tablatures.md

@@ -77,9 +77,9 @@ then quickly release the first, letting the second ring.
 }
 ```
 
-It is possible to add "H" and "Po." markers,
+It is _possible_ to add "H" and "Po." markers,
 but the syntax is ugly.
-They are not ubiquitous anyway.
+They are not ubiquitous or especially helpful anyway.
 
 ### String Bending
 

conduit-sizing.md

@@ -1,34 +1,14 @@
 ---
 id:
 aliases: []
+title: Conduit Sizing
 tags:
+  - authorship/original
   - destiny/fleeting
   - status/incomplete
   - topic/construction/electrical
   - type/encyclopedia
-  - authorship/original
-title: Conductor Sizing
 ---
 # Conduit Sizing
 
-Table 1 Percent of Cross Section of Conduit and Tubing for Conductors and Cables
-
-| Number of Conductors and/or Cables | Cross-Sectional Area (%) |
-| ---------------------------------- | ------------------------ |
-| 1                                  | 53                       |
-| 2                                  | 31                       |
-| Over 2                             | 40                       |
-
-> [!info] Informational Note No. 1:
-> Table 1 is based on common conditions of proper cabling and alignment of conductors
-> where the length of the pull and the number of bends are within reasonable limits.
-> It should be recognized that, for certain conditions,
-> a larger size conduit or a lesser conduit fill should be considered.
-
-> [!info] Informational Note No. 2:
-> When pulling three conductors or cables into a raceway,
-> if the ratio of the raceway (inside diameter)
-> to the conductor or cable (outside diameter)
-> is between 2.8 and 3.2, jamming can occur.
-> While jamming can occur when pulling four or more conductors or cables into a raceway,
-> the probability is very low.
+![[nfpa-70_ch09#Table 1 Percent of Cross Section of Conduit and Tubing for Conductors and Cables|Table 1 Percent of Cross Section of Conduit and Tubing for Conductors and Cables]]

nfpa-70_ch09.md

@@ -0,0 +1,36 @@
+---
+id:
+aliases:
+  - nec-ch9
+title: Chapter 9 Tables
+tags:
+  - authorship/other
+  - destiny/permanent
+  - exclude-from-word-count
+  - status/incomplete
+  - topic/construction/electrical
+  - type/media/reference
+---
+# Chapter 9 Tables
+
+## Table 1 Percent of Cross Section of Conduit and Tubing for Conductors and Cables
+
+| Number of Conductors and/or Cables | Cross-Sectional Area (%) |
+| ---------------------------------- | ------------------------ |
+| 1                                  | 53                       |
+| 2                                  | 31                       |
+| Over 2                             | 40                       |
+
+> [!info] Informational Note No. 1:
+> Table 1 is based on common conditions of proper cabling and alignment of conductors
+> where the length of the pull and the number of bends are within reasonable limits.
+> It should be recognized that, for certain conditions,
+> a larger size conduit or a lesser conduit fill should be considered.
+
+> [!info] Informational Note No. 2:
+> When pulling three conductors or cables into a raceway,
+> if the ratio of the raceway (inside diameter)
+> to the conductor or cable (outside diameter)
+> is between 2.8 and 3.2, jamming can occur.
+> While jamming can occur when pulling four or more conductors or cables into a raceway,
+> the probability is very low.

nfpa-70_national-electric-code.md

@@ -195,7 +195,9 @@ title: "NFPA 70: National Electric Code"
 * [[nfpa-70_830|830 Network-Powered Broadband Communications Systems]]
 * [[nfpa-70_840|840 Premises-Powered Broadband Communications Systems]]
 
-## Chapter 9 Tables
+***
+
+* [[nfpa-70_ch09|Chapter 9 Tables]]
 
 * [[nfpa-70_anx-a|Annex A: Product Safety Standards]]
 * [[nfpa-70_anx-b|Annex B: Application Information for Ampacity Calculation]]