111 lines
3.4 KiB
Markdown
111 lines
3.4 KiB
Markdown
---
|
|
tags:
|
|
- occupational/takeoff
|
|
- status/draft
|
|
- type/guide
|
|
title: Lighting Controls Takeoff
|
|
up: "[[takeoff-scripts]]"
|
|
aliases:
|
|
- lighting controls takeoff
|
|
---
|
|
# Lighting Controls Takeoff
|
|
|
|
> [!info]
|
|
> See [[lighting-controls]] for more on lighting controls systems
|
|
> and [[lighting-controls-research]] for PDI considerations.
|
|
|
|
> [!info] "Local Control" as a PDI proposal qualification
|
|
> The term "local control only" is sometimes used to indicate
|
|
> no consideration for _any_ lighting control beyond standard devices,
|
|
> (with `$D`'s being the [[lighting-controls#Triac Dimming|triac]] type)
|
|
> however, this phrasing is ambiguous and non-universal.
|
|
> Confirm with [[pdi-bid-estimating|bid team]] on what must be included.
|
|
|
|
Determine which Systems and Codes are required:
|
|
* _IBC/IECC 2021 or later:_ all fixtures 0-10V dimmable.
|
|
|
|
* `System` = "LV - Lighting Control System"
|
|
|
|
## Wall Switches
|
|
|
|
> [!tip]
|
|
> For switch combinations not in `COMMON ASSEMBLIES`,
|
|
> create [[heating-designations]] based on the most similar.
|
|
|
|
## Analog Controls
|
|
|
|
24V sensors. Typical of BOH spaces too large for wall sensors.
|
|
|
|
1. `COMMON ASSEMBLIES`/`SWITCHES`/`CEILING OCC SENSOR ...`
|
|
**Count:** as shown.
|
|
|
|
2. `COMMON ASSEMBLIES`/`SWITCHES`/`POWER PACK FOR OCC SENSOR ...`
|
|
**Count:** each circuit controlled by analog sensors. Minimum 1 per sensor.
|
|
|
|
## Digital Controls
|
|
|
|
Applicable to all digital control systems
|
|
(i.e. "Standalone" and "Centralized", wired and wireless)
|
|
|
|
### General
|
|
|
|
Takeoff normal power to the controlled load
|
|
* Add LV cable to fixture branch
|
|
* Use switched assemblies (\#12/3) for controlled receptacles
|
|
|
|
#### Digital Sensors
|
|
|
|
1. `COMMON ASSEMBLIES`/`SWITCHES`/`LOW VOLTAGE SWITCHES & OCC SENSORS - ROUGH IN`/...
|
|
* `... LV SW - WALL ROUGH IN ...`
|
|
* `... SENSOR LOW VOLTAGE - ROUGH IN ...`
|
|
|
|
### "Standalone" Systems
|
|
|
|
Room controllers distributed throughout controlled areas.
|
|
|
|
> [!important] "Room controllers"
|
|
> As I have always understood it, and other manufacturers tend to agree,
|
|
> a room controller _necessarily_ controls multiple zones
|
|
> (otherwise "zone controller" would be better),
|
|
> however PDI terminology is based on Wattstopper's.
|
|
|
|
`COMMON ASSEMBLIES`/`SWITCHES`/`LOW VOLTAGE SWITCHES & OCC SENSORS - ROUGH IN`/...
|
|
|
|
1. .../`DLM LTG RM CONTROLLER - ...`
|
|
**Count:** each lighting control zone.
|
|
|
|
2. .../`REC PLUG CONTROLLER - ...`
|
|
**Count:** each receptacle control zone.
|
|
|
|
3. `HEATING`/`Network Bridge - Blank 4SQ`
|
|
**Count:** each controller.
|
|
|
|
Coordinate with PDS to determine if necessary.
|
|
|
|
4. `COMMON ASSEMBLIES`/`PDI BRANCH CKT HOME RUNS`/... (_without_ dimming cable)
|
|
**Count:** each _circuit_.
|
|
|
|
### "Centralized" Systems
|
|
|
|
Zones switched and dimmed from central lighting control panel (LCP).
|
|
|
|
1. `COMMON ASSEMBLIES`/`DISTRIBUTION`/`LIGHTING CONTROL PANEL INSTALLATION`/...
|
|
|
|
2. `COMMON ASSEMBLIES`/`PDI BRANCH CKT HOME RUNS`/... (_with_ dimming cable)
|
|
**Count:** each _lighting control zone_.
|
|
|
|
### Somewhere In Between
|
|
|
|
The dichotomy of [[#"Standalone" Systems]] vs. [[#"Centralized" Systems]]
|
|
assumes zones will be controlled either
|
|
(1) right next to the fixture or (2) in the nearest electrical room.
|
|
|
|
I think just as common is 3--5 circuit controllers above the ceiling.
|
|
|
|
1. `HEATING`/`Lighting Control Room Controller - n Circuit`
|
|
**Count:** each controller.
|
|
|
|
2. `COMMON ASSEMBLIES`/`PDI BRANCH CKT HOME RUNS`/... (_without_ dimming cable)
|
|
**Length:** route to room.
|
|
**Count:** each circuit.
|