vault backup: 2025-11-18 16:52:01

2025-11-18.md

@@ -0,0 +1,60 @@
+---
+id:
+aliases: []
+tags:
+  - authorship/original
+  - destiny/permanent
+  - status/draft
+  - type/daily
+title: ""
+---
+# 2025-11-18
+
+## 2025-11-18 16:33
+
+%%
+Transcription of notes
+taken while reviewing Elliot St. with Joel Jansen.
+%%
+
+Adorne USB Heating Designation was built with standard device.
+Subbed for Adorne.
+
+Subbed standard duplex receptacles in guestrooms for Adorne.
+
+Confirmed fixture branch length changes
+including Garage
+
+Note: It is not usually necessary to count emergency fixtures separately.
+
+Use minimum 1 hour for tape lights, except in units (minimum 0.5hr).
+
+Final Pricing adjustments:
+Warranty,
+CIP (see proposal)
+
+Added putty pads.
+
+Fire stopping budget = $25-35 per Unit.
+
+Robotic Total Station hours: match Structural Foreman.
+
+Equipment Cost $\approx$ 1% for contracts 5-15 million dollars.
+
+Mid Atlantic: 1 trip per month
+
+Offsite Parking: see bid sheet
+
+Project Executive time same as Oversight.
+
+When calculating durations for indirect labor, round down.
+
+* Rough Foreman
+* Trim Foreman
+* Amenity Foreman
+
+LV/FA Foreman: get hours from systems quote.
+
+Fire Alarm, Two-Way Communication, DAS: `Phase` = "Fire Alarm"
+
+Erroneously used WP GFI's in bathrooms, subbed for Kitchen/Bath assembly.

fire-alarm-takeoff.md

@@ -141,11 +141,15 @@ Vertical:
 
 ### Smoke Detectors
 
+`COMMON ASSEMBLIES`/`FIRE ALARM & DAS SYSTEMS`/`INITIATING DEVICES WITH WIRE - ...`/`SMOKE DETECTOR W/ BASE - ...`
+
 _Design Build:_
 Count every stairwell at every level.
 
 ### Pull Stations
 
+`COMMON ASSEMBLIES`/`FIRE ALARM & DAS SYSTEMS`/`INITIATING DEVICES WITH WIRE - ...`/`PULL STATION - ...`
+
 _Design Build:_
 Count every stairwell at every level
 and every exterior exit.
@@ -165,7 +169,9 @@ _Design Build:_
 Count 2 for every set of double doors.
 (Typical of elevator lobbies and corridors)
 
-### Speaker Strobes
+### Horns, Speakers, and Strobes
+
+`COMMON ASSEMBLIES`/`FIRE ALARM & DAS SYSTEMS`/`INDICATING DEVICES WITH WIRE - ...`/`INDOOR HORN STROBE - ...`
 
 _Design Build:_
 * Count every 75 ft,

pdi-labor-plan.md

@@ -2,38 +2,37 @@
 id:
 aliases: []
 tags:
+  - authorship/other-for-now
   - destiny/permanent
   - occupational
   - status/incomplete
   - type/guide
-  - authorship/other-for-now
 title: PDI Labor Plan
 ---
 # PDI Labor Plan
 
 1. Fill out project basics
 
-2. Check that everything is sorted into correct Phase and Area (Extension: Phase - Area)
+2. Check that everything is sorted into correct `Phase` and `Area` (Extension: Phase - Area)
 
 3. Move everything in BUILDING FA systems into FA phase
 
-    * Create a Phase named: "Fire Alarm"
+    * Create `Phase` = "Fire Alarm"
-    * Check system and Bid Item
+    * Check `System` and `Bid Item`
     * Scroll through each and select all line items `FA - ...`
-    * Change Breakdown to "Fire Alarm" phase
+    * Set `Phase` = "Fire Alarm"
 
-4. Separate all Phases into their proper corresponding "Labor Factor"
+4. Separate all Phases into their proper corresponding `Labor Factor`
 
-    * Check Phase box
+    * Scroll through each `Phase`
-    * Start scrolling through beginning with N/A
+    * Change breakdown of everything in each phase to the proper `Labor Factor`
-    * Change breakdown of everything in each phase to the proper labor factor
     * Do not move Temp Power (buckets) or site
 
 5. Use the Accubid Extension tab to fill out the "Unit Lbr Calc" tab in the labor plan
 
-6. Select the "Phase / Sort Code" extension view
+6. Select extension view "Phase / Sort Code"
 
-7. Open "UNIT RESIDENTIAL" and "Building - Corridors" phases
+7. Open `Phase` "UNIT RESIDENTIAL" and "Building - Corridors"
 
 8. Go into each Sort code to find the count for each unit item
 
@@ -50,14 +49,14 @@ title: PDI Labor Plan
 10. Fill out the "Labor for Concrete Slab/Deck Labor" table on the labor sheet calc tab
 
     * For the floor counts, if there are multiple buildings, add their total level count together
-
         * 2 buildings that each have 10 floors, input 20 for "number of floors - building
     
     * Add any useful description to the naming
         * Can change "Other" to something more prevalent on the project
     
-    * "pour section rate" refers to the size of each slab that will be poured (sometimes will be shown on the structural plans)
+    * "pour section rate" refers to the size of each slab that will be poured
+        * sometimes will be shown on the structural plans
     
-    * "Number of days per…" is found by multiplying "Pour Section Qty" by 4 or 5
+    * "Number of days per..." equals "Pour Section Qty" times 4 or 5
 
-11. Check that everything is sorted into correct Phase and Area (Extension: Phase - Area)
+11. Check that everything is sorted into correct `Phase` and `Area` (Extension: "Phase - Area")

telecom-takeoff.md

@@ -38,6 +38,10 @@ Size and quantity per proposal > drawings > assume (4) 4"C
 
 _Garden Style:_ Outside of every building
 
+> [!important] Long-Radius Elbows
+> Note requirements for long-radius elbows,
+> substitute items as necessary.
+
 ### Telecom Vaults
 
 "Quazite Box"
@@ -117,3 +121,6 @@ As shown on plans. Ignore floor boxes, other electrical scope.
 * .../`BOH / AMENITY ASSEMBLIES`
 * .../`SCREWLESS DECORA COVERS UNITS / BOH`
 * .../`ROUGH IN ASSY`
+
+If system is included, take off _both_ rough-in and device assemblies
+in amenity areas.

units-takeoff.md

@@ -98,8 +98,16 @@ Eaton 35M2W
 
 ### Telecom Homeruns
 
+#### Residential
+
 Included in MSDE.
 
+#### Key
+
+`COMMON ASSEMBLIES`/`TELECOM SYSTEMS`/`BOH AMENITY ASSEMBLIES`/...
+
+Adjust cable length as needed.
+
 ### Fire Alarm Devices
 
 #### Residential
@@ -116,4 +124,6 @@ For ADA units:
 
 ##### Additional Signaling Devices
 
-==use free air devices==
+`COMMON ASSEMBLIES`/`FIRE ALARM & DAS SYSTEMS`/`INDICATING DEVICES WITH WIRE - ...`/`UNIT HORN/STROBE - ...`
+
+#### Key